Contact Us Today!

Or, fill out this short form and we will contact you

We make it easy!™

 

Easy-Laser® is a registered trademark of Damalini AB in the United States and/or other countries.

Laser Accessories

One of the best aspects of our Easy-Laser® systems is how flexible and versatile they are.  We have an amazing selection of optional accessories - everything from brackets to laser transmitters listed below.  We can even create new fixtures as necessary, so if you have a particular need, don't hesitate to ask us about it! 

FOR DOCUMENTATION

 

 

  

Portable Thermal Printer

03-0341

Includes cable and charger for 110V or 220V power source. 

(Printer included  in systems D650 and D660.)

      

       

EasyLink™ Software

 

Database and documentation software for Windows®. Included in all systems.
Barcode reader

The barcode reader is used to enter the machine data before measurement. At the first measurement of the machine apply the adhesive bar code label. Next time the machine is checked the dimensions are read in directly. Connected in the USB port.

NOTE: Barcode reader for use with E-Series systems only.

FOR VIBRATION MEASUREMENT

 

 

D-Series Vibrometer Probe

12-0283

 For measuring vibration level (inch/s) or (mm/s) plus bearing condition (g-value). For systems with “Vibrometer” software.

E-Series Vibrometer Probe

12-0285

For measuring vibration (mm/s, inch/s) and bearing condition (g-value). For systems with program "Vibrometer" in Display unit E418.

Only for use with the E-series.

FOR E-SERIES SHAFT ALIGNMENT

Additional power supply with built-in Bluetooth® unit

 Chargeable battery pack which gives extra operating time. Connected with the included cable. Charging status shown with LED.
Additional power supply Chargeable battery pack which gives extra operating time. Connected with the included cable. Charging status shown with LED.

Charger 
12-36V

12-0585

 To charge the display unit via 12-36 V socket, for example in a car.

 Target

12-0588

 Simplifies the rough alignment at very long distance and large alignment fault.
 Sun Visor To screen against extremely strong ambient light.

 VGA kit

12-0573

 Makes it possible to show display unit screen image with a projector, for example in a training context. Must be factory installed on order.

FOR SHAFT ALIGNMENT (D-SERIES & E-SERIES)

 

 

Sliding Bracket

12-0039

 Used when the shafts cannot be rotated.

 

 

Thin Chain Bracket

12-0412

 Used when space is limited between the coupling flange and end-bell.

 

 

Magnetic Fixture

12-0413

 For axial mounting on flanges, hubs, or shafts.

 

 

Cardan Bracket

12-0125

 For angular alignment of flanges on offset mounted machines.

 

 

 

Magnetic Base

12-0013

 Provides alternate mounting options of detector on flanges or shafts. (Included in system D505/D525)

 

 

Offset Bracket

01-0076

 For axial displacement of the measuring units. (Included in system D505/D525)
   

FOR SHEAVE/PULLEY ALIGNMENT

 

 

D160

Digital Belt Alignment

For aligning sheaves/pulleys. The D160 detector can be connected to our D480, D505, & D525 shaft alignment systems for foot corrections and documentation. 

Requires firmware version 1.06 or later.

FOR GEOMETRIC MEASUREMENT

 

 

Rotating Laser D22

12-0022

 For measuring flatness, straightness, squareness, plumb, parallel and spindle direction. The laser beam can sweep 360°, measurement distance: 40 meters. The beam can be deflected 90° to the sweep to within 0.01 mm/m.

 

 

Spin Laser D23

12-0168

 The motorized rotating head projects a 360° laser plane for a quick measurement of flatness or straightness. Requires a D6 Detector.

 

 

Laser Transmitter D75

12-0075

 For measuring straightness and spindle direction. M6 threads on ends and sides offer alternative mounting options. Measurement range: 40 meters. Also available in Long-Range version for 60 meters.

 

 

 

  

  

Laser Transmitter D75 Truebeam

12-0075T

 For measuring straightness and spindle direction. M6 threads on ends and sides offer alternative mounting options. Measurement distance: 80 meters.

 

 

Spindle Laser D146

12-0146

For measuring spindle pointing direction and straightness. Can be  rotated up to 2000 rpm max. 

Face or rear mount to fit different collett sizes. Measurement distance: 20 meters.

 

 

Detector D5

12-0005

 

2-axis Detector (PSD) with 360° electronic inclinometers. A number of mounting holes and threads make alternative attachment possible.

 

 

Detector D6

12-0006

Reads the position of the laser beam in 1-axis.  A number of mounting holes and threads make alternative attachment possible. Used with Laser Transmitter D23.

 

 

Detector D157

12-0157

 2-axis Detector with 360° electronic inclinometers. A number of mounting holes and threads make alternative attachment possible. Two alternative connectors for connection to display unit and other detectors. Diameter 40 mm, length 60 mm.

 

 

TDM Unit 

12-0116

 Laser transmitter and detector in one housing. Reads the position of the laser beam in two directions 2-axis PSD, includes 360° electronic incliniometers.

 

 

Angular Prism D46

12-0046

 Used to measure squareness and parallel. The built-in penta prism deflects the beam 90° from the source.

 

 

Magnetic Fixture for D75

12-0187

 With three magnets for mounting on shaft ends, flywheels etc.

 

 

 

 

        

Magbase w/ Turnable Head

12-0045

 Allows you to rotate the detector square to the beam. Especially helpful when measuring flatness on flanges or flat surfaces.

 

 

Sliding Bracket w/ Turnable Head

12-0137

 Used on roll parallel measurement to square beam to the laser transmitter. Can be mounted with standard chains or magnets.

 

 

Heavy Duty Tripod

12-0269

 For laser transmitter D22 and angular prism D46. Height 500-2730 mm.

 

 

Parallelity Kit

12-0203

 Contains: (2) Floor targets with monument probe for laser "buck-in" procedure. Coordinate table for fine adjustment of the D22 Transmitter or D146 Angular Prism. Magbase with Turnable Head and Sliding Fixture with Turnable Head.